Dry, Aqueous, or Organic Solvent Dispersion? Configuring Laser Diffraction and Dynamic Image Analysis for Cement Research
2026-11-17News
Key Takeaway: Choose the cement dispersion method based on the sample state. Start by evaluating dry dispersion for routine QC of dry powders, and consider compatible alcohol-based wet methods for liquid dispersion and morphology studies. For aqueous methods, establish how hydration affects the measurement. With the appropriate dispersion units and PIC-1, the Bettersizer 2600 Plus supports dry particle sizing and wet particle size and shape studies.
Whether cement enters the instrument as a dry powder, an alcohol suspension, or a sample that has contacted water affects what the particle size result represents. Define the measurement target first, then choose the dispersion method. This provides a common starting point for comparing distributions, transferring methods, and evaluating configurations.
Define the Sample State Before Choosing the Dispersion Medium
A dispersion medium should deliver particles uniformly into the measurement zone while preserving the sample state required by the study. Dry dispersion is an option for powders that readily react with liquids. For wet analysis, select a liquid that wets the particles and is compatible with the sample. Aqueous and organic solvent dispersion are the two wet routes considered here.
Unhydrated cement reacts with water, changing the sample state during measurement. NIST research on cementitious powders discusses alcohol media, including isopropanol. Liquid selection should account for wetting and dispersion performance, as well as the medium's effects on sample reaction, dissolution, and changes in particle size.
A practical selection sequence follows: first establish whether the target is unhydrated powder or a sample under defined liquid conditions; then confirm medium compatibility; finally, decide whether particle images and shape parameters are needed.
Dry Dispersion: A Starting Point for Routine Cement Particle Size QC
Dry dispersion uses compressed gas to carry powder into the measurement zone and disperses agglomerates through shear and collisions. It removes the liquid-selection step and is a useful first option to evaluate for routine sizing of dry cement.
Dispersion pressure is central to dry method development. Increase pressure step by step and compare the complete size distribution and key percentiles. The aim is to identify a stable operating region that provides effective deagglomeration while preserving particle integrity.
In one of our cement studies, dry and wet measurements of grade 32.5 cement produced similar D50 values; the dry result had a smaller D10 and a slightly larger D90. Dispersion mechanisms provide a starting point for investigating such differences: dry methods use gas-flow shear and collisions to disperse agglomerates, while wet methods can use wetting, circulation, and suitable ultrasonication. Compare the dispersion state alongside the full distribution to locate differences at the fine and coarse ends.
Table 1. Dry and wet particle size results for grade 32.5 cement
|
Grade 32.5 cement |
D10 (μm) |
D50 (μm) |
D90 (μm) |
|---|---|---|---|
|
Wet |
1.912 |
11.41 |
32.56 |
|
Dry |
1.525 |
11.57 |
33.85 |
Source: Table 1 of the cement application note; typical results as reported. D10, D50, and D90 are the particle sizes at 10%, 50%, and 90% of the cumulative distribution, respectively. Use the same distribution basis when making comparisons.
In the 1–4 bar pressure titration for this grade 32.5 cement, D50 decreased as pressure increased. The results at 3 bar and 4 bar were 11.17 μm and 11.13 μm, respectively, showing that the change became smaller. Laboratories can use the same sequence—increase pressure in steps, compare complete curves, and identify a stable region—to establish the operating pressure while checking particle integrity. The cement application note provides the complete pressure curves and repeated-measurement results.
Organic Solvent Wet Dispersion: A Liquid Measurement Route for Water-Sensitive Powders
When cement needs to be measured in a liquid while reducing hydration interference, evaluate compatible alcohol-based organic solvents. Isopropanol (IPA) is commonly used in cement particle size method studies. The choice of medium depends on dispersion performance, sample stability during measurement, and compatibility with the instrument's wetted flow path.
Circulation and stirring help keep particles suspended, while ultrasonication can assist deagglomeration. During method development, evaluate pump speed, ultrasonic intensity, and treatment time together. If the fine fraction changes with ultrasonication, determine whether the change reflects deagglomeration or alteration of the particles themselves before fixing the conditions.
Traceability of wet results should include medium purity, water content, contact time, and medium replacement records. Monitor temperature when evaluating ultrasonic conditions to avoid overheating the sample: NIST's cement–alcohol dispersion study used cooling measures for this purpose. Saving these preparation conditions alongside the particle size results helps investigate shifts between testing days.
The Bettersizer 2600 cement report using organic solvent wet dispersion, white Portland cement report using ethanol wet dispersion, and white Portland cement report using dry dispersion illustrate reporting formats for the different routes.
Aqueous Dispersion: Define the Sample State and Measurement Timing
Aqueous dispersion suits samples that retain the target state during measurement. Because unhydrated cement hydrates in water, prioritize evaluating dry methods or compatible organic solvent wet methods for that material. When studying behavior after contact with water, define the starting point for contact time, the medium composition, and how the results will be interpreted.
Aqueous wet methods also support particle size studies of cement raw materials. For example, a calcium carbonate test used water as the medium. A Pennsylvania State University study of circulating fluidized bed fly ash also used distilled water for laser diffraction sizing. For supplementary materials such as finely ground slag and silica fume, choose the medium according to each material's reactivity with water, wetting behavior, and dispersion performance. Establish methods separately for the raw materials and the final cement blend.
When Should Dynamic Image Analysis Be Added?
Laser diffraction (LD) provides the size distribution of a particle population. Dynamic image analysis (DIA) extracts size and shape information from particle images. When R&D teams compare new raw materials or additives, or investigate an unusual coarse tail, images help reveal irregular particles and agglomerates, adding visible morphological evidence to the size distribution.
On the Bettersizer 2600 Plus, PIC-1 works with a suitable wet dispersion unit to bring laser diffraction distributions and dynamic images into the same wet measurement workflow. Laboratories can use the same analyzer for routine dry sizing and wet morphology studies.
The Bettersizer 2600 Plus has a wet laser diffraction range of 0.02–2,600 μm and a dry range of 0.1–2,600 μm. PIC-1 dynamic image analysis covers 2–3,500 μm. Laser diffraction captures the distribution of fine particles, while dynamic imaging adds information about the appearance and agglomeration of larger particles, helping relate changes at the coarse end to visible particle morphology.
Which Tasks Do BT-912, BT-812, BT-80N, and PIC-1 Support?
The following configurations pair laboratory tasks with dispersion and imaging components for the Bettersizer 2600 Plus.
Table 2. Dispersion and imaging configurations for the Bettersizer 2600 Plus
|
Laboratory task |
Dispersion and imaging |
Information obtained |
Selection focus |
|---|---|---|---|
|
Routine QC of dry cement |
BT-912 |
Dry LD size distribution |
Validate dispersion pressure and stable feeding |
|
Aqueous wet sizing of compatible samples |
BT-812 |
Aqueous wet size distribution |
Confirm compatibility with water |
|
Organic solvent wet sizing |
BT-80N or BT-80N Pro |
Solvent wet size distribution |
Confirm solvent compatibility and automation needs |
|
Aqueous wet size and shape studies |
BT-812 + PIC-1 |
Size distribution and dynamic images |
Confirm suitability for aqueous dispersion |
|
Organic solvent wet size and shape studies |
BT-80N Pro + PIC-1 |
Particle size and dynamic images in solvent |
Use BT-80N Pro + PIC-1 for combined sizing and imaging |
Choose the organic solvent unit according to the information required: evaluate BT-80N or BT-80N Pro for particle sizing, and use BT-80N Pro + PIC-1 for combined sizing and dynamic imaging in a wet configuration.
Begin configuration planning with the laboratory's main task. For routine release testing of particle size, start with the dry route. Add a validated solvent wet method and imaging workflow when the laboratory also develops formulations or compares raw materials. This makes the budget justification specific: which samples each module serves, what information it produces, and which decisions it supports.
Turn the Configuration Choice into a Reusable Test Method
When moving from exploratory work to routine testing, document these four elements in the method.
- Define the measurement target: Record the sample identifier, storage conditions, and sampling method. Specify whether the target is unhydrated powder or a sample under defined liquid conditions.
- Validate dispersion conditions: Compare pressure levels for dry methods. For wet methods, compare media, circulation, and ultrasonic conditions, and check stability during measurement.
- Retain the complete results: Review D10, D50, D90, and the full distribution together. For morphology studies, also record the images and the shape metrics used.
- Establish the relationship between methods: When switching between dry and wet methods, compare representative samples in paired tests, then define the intended use and acceptance criteria for the results.
Choose the dispersion medium based on the sample state, then configure the measurement modules according to the size and shape information required. This connects cement laser diffraction and dynamic image analysis to practical QC and R&D tasks.
Choosing a dispersion route for your cement samples? Submit sample information through the Bettersize Free Sample Testing page, including water sensitivity, your current method, and whether shape data are needed. The application team can discuss suitable measurement and configuration options with you.
Frequently Asked Questions
1. Should cement particle size be measured by dry or wet laser diffraction?
Choose according to sample state and information needs. Evaluate dry methods first for routine sizing of dry powders, and compatible wet methods when liquid dispersion or combined size and shape analysis is needed. Cement hydrates in water, so the wet medium must match the measurement objective.
2. Can cement be dispersed directly in water for wet laser diffraction?
For unhydrated cement powder, prioritize dry methods or compatible organic solvent wet methods. Water induces hydration. An aqueous method therefore requires a defined measurement time and validation of sample changes within that period.
3. Why is isopropanol used for cement particle size analysis?
Isopropanol is one of the alcohol media used to reduce hydration interference in cement particle size studies. During method development, confirm dispersion performance, sample stability, and compatibility with the instrument's wetted flow path together.
4. Can dry and organic solvent wet results be used interchangeably?
For method transfer or assessment against specified limits, first compare representative samples in paired tests to establish the relationship between dry and wet results. The grade 32.5 cement in the application note had similar D50 values but differences in D10 and D90.
5. What configuration measures particle size and shape in an organic solvent?
For the Bettersizer 2600 Plus, the combined organic solvent configuration is BT-80N Pro + PIC-1. For wet sizing alone, evaluate BT-80N or BT-80N Pro. The selected solvent must be compatible with the instrument's wetted flow path.
6. Is dynamic image analysis needed if laser diffraction already provides a size distribution?
Dynamic image analysis adds morphological evidence when you need to examine shape, irregular particles, or agglomerates. Start with laser diffraction for routine particle size QC, then determine imaging needs from the R&D question and the actual particle sizes in the sample.
|
FURTHER READING / APPLICATION NOTE Want to explore this study further? Read the original application note for the full experimental methods, data, and findings. Read the Original →Laser Diffraction · Particle Size Distribution |
|
Recent News









