bettersize
0
bettersize
0
Building Materials banner

Cerámica

Introduction

Los instrumentos de Bettersize ofrecen análisis del tamaño de partículas para productos cerámicos durante el proceso de fabricación.

  

En la producción de cerámica, un tamaño de partícula adecuado del cuerpo preformado, el esmalte y los pigmentos puede mejorar la calidad del producto. Los cambios que pueden producirse en los productos finales, especialmente durante la sinterización, dependen en gran medida de las propiedades del polvo inicial y están estrechamente relacionados con el tamaño de partícula. Una distribución ideal del tamaño de partículas en el cuerpo preformado puede mejorar la densidad de la estructura y aumentar la resistencia de la porcelana, mientras que un tamaño de partícula más pequeño en el esmalte mejora la suavidad de la superficie. Cuando el tamaño de partícula del cuerpo preformado y del esmalte alcanza la escala nanométrica, la porcelana presenta mayor tenacidad, lo que amplía el rango de aplicaciones de los materiales cerámicos.

 

En la producción de sanitarios cerámicos, la suspensión final no debe molerse en exceso para evitar la generación de demasiadas partículas finas, ya que estas pueden bloquear los poros del molde, impidiendo la salida del exceso de agua y debilitando el producto conformado antes de su cocción en el horno.

 

En el proceso de producción de materiales cerámicos, es posible medir con precisión la distribución del tamaño de partículas, la forma de las partículas, las características del polvo y otras propiedades del cuerpo preformado, el esmalte y los pigmentos. 

Citations

  • Bettersizer 2600

    Functional redundancy as an indicator for evaluating functional diversity of macrobenthos under the mussel raft farm near Gouqi Island

    DOI: 10.1016/j.aquaculture.2023.740024 Read Article Go logo
    Zhejiang Ocean University | 2024
    Biological traits analysis (BTA) helps to evaluate the effects of different environmental variables on the traits-based functional composition of macrobenthos. However, research on functional traits of macrobenthos under mussel farming is limited. We investigated the spatial and temporal response of the benthic system in terms of taxonomic and functional diversity to environmental variables of farming and natural stressors resulting from suspended mussel farming near Gouqi Island of eastern China Sea. The functional traits of macrobenthic assemblages under mussel farming were characterized by “medium adult body size”, “vermiform body form”, “high flexibility”, “infauna”, “semi-motile”, “gonochoristic”, “surface deposit-feeders”, “carnivores”, “semi-motile burrowers”, and “tube-dwellers”. Functional redundancy was stable in response to mussel farming stresses among seasons, whereas species diversity showed efficient to evaluate natural variables. Functional diversity was significantly affected by farming stressors rather than natural variables, Further analysis using multivariate methods together with continuous monitoring were highlighted to evaluate the impacts of mussel farming. Our results reinforce the importance of macrobenthic species and functional traits analysis to evaluate human stresses driven impacts in offshore ecosystems. By analysing the environmental variables with different sources, independently, we concluded the main effects of human pressures on macrobenthic community. Such distinction could be particularly effective to isolate variable environmental descriptors and evaluate their effects on functional diversity, making the current approach promising for the evaluation of ecological effects of anthropogenic stressors in aquaculture areas.
  • Bettersizer 2600

    Degradation characteristics and utilization strategies of a covalent bonded resin-based solid amine during capturing CO2 from flue gas

    DOI: 10.1016/j.seppur.2023.125621 Read Article Go logo
    China University of Petroleum | 2024

    In this study, various types of degradation as well as attrition which are possibly encountered in a circulating fluidized bed temperature swing adsorption (CFB-TSA) process, were conducted experimentally to evaluate the stability of a resin-based solid amine sorbent. Other characterizations methods, such as elemental analysis (EA), Fourier transform infrared spectroscopy (FTIR) etc. were applied to further reveal the degradation mechanisms. The results showed that thermal degradation occurs from 140–160 °C due to the decomposition of amine group. The CO2-induced degradation occurs from a higher temperature of 160–180 °C accompanied by the production of urea. Hydrothermal stability is good below 130 °C, but the ionic impurities in steam crystalized on particle surface can accelerate the degradation. Oxidative degradation is the most harmful, which starts at a lower temperature of 70–80 °C with the formation of aldehyde. The existence of H2O in atmosphere can alleviate the oxidative and CO2-induced degradations. The employed sorbent has a very low attrition index of 0.05, which is 1–2 orders lower than typical commercial fluidized bed catalysts. Based on the results of stability evaluation, some design suggestions for proper utilization of this sorbent or other similar resin-based sorbents have been provided in an industrial CFB-TSA process.

  • Bettersizer 2600

    De-branching of starch molecules enhanced the complexation with chitosan and its potential utilization for delivering hydrophobic compounds

    DOI: 10.1016/j.foodhyd.2023.109498 Read Article Go logo
    Shihezi University | 2024
    The current study aimed to prepare the complexes between debranched-waxy corn starch and chitosan polymers (DBS-CS), and then investigated their corresponding structural characteristics, rheological property and potent application in Pickering emulsion. The results indicated that the existence of chitosan significantly inhibited starch short-range molecular rearrangement for all DBS-CS samples, which was manipulated by both debranching treatment and chitosan content. Interestingly, this is the first study to reveal that the outstanding peak at 1.8 ppm in 1H NMR spectrum for sample DBS-CS was gradually shifted towards a lower-field region following an increased chitosan content. Moreover, the debranching treatment shifted the crystallinity pattern from A-type to B-type and the relative crystallinity of DBS-CS decreased gradually with the increased content of CS. All samples had a pseudoplastic fluid and shear-thinning behavior with an enhanced shear resistance following the complexation. The DBS-CS was applied in a Pickering emulsion for showing a greater emulsifying stability and a lower gel strength than native NS-CS prepared emulsion. Importantly, the encapsulation ability of curcumin in the DBS-CS emulsion was significantly improved, followed by an increase of 15.45% for its corresponding bioavailability compared to the control. Therefore, this study might highlight a potential carrier for delivering the bioactive substances in a green pattern.
  • Bettersizer 2600

    Heat-induced aggregation behavior of wheat gluten after adding citrus pectin with different esterification degree

    DOI: 10.1016/j.foodhyd.2023.109420 Read Article Go logo
    Gansu Agricultural University | 2024
    Wheat gluten aggregation during heat treatment is beneficial to the final quality of gluten-based products. Exogenous pectin can affect gluten aggregation. However, the effect of pectin with different degrees of esterification on the heat-induced aggregation behavior of gluten and its possible mechanism are still unclear. Thus, the heat-induced aggregation behavior of gluten after adding pectin with different esterification degree was studied in this study. When the temperature was raised from 25 °C to 95 °C, pectin affected gluten aggregation and was related to the degree of esterification. Specifically, the results of rheological properties and particle size indicated that low-ester pectin improved the viscoelasticity of gluten and promoted gluten aggregation. Thermal properties revealed that enthalpy of gluten added with low-ester pectin (37%) increased from 92.96 J/g to 95.40 J/g during heating process. Structurally, the fluorescence intensity and surface hydrophobicity of gluten added with low-ester pectin (37%) were lower than those added with high-ester pectin (73%). In addition, low-ester pectin (37%) significantly increased the disulfide bond content (from 15.31 μmol/g to 18.06 μmol/g) and maintained β-sheet content of gluten compared with gluten alone at 95 °C, indicating that low-ester pectin was more likely to induce gluten aggregation. However, scanning electron microscope showed that the gluten added with low-ester pectin (46%) exhibited a denser network structure at 95 °C than that added with low-ester pectin (37%). These results will provide a theoretical base for the regulation of gluten aggregation and the quality of gluten-based products by pectin with different esterification degree.
Page 1 of 84
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 84
Go to

Recursos seleccionados

  • Application Note
    Structural Insights into Thermally Expandable Alumina Microspheres via True Density Measurement

    2025-10-21

    Análisis estructural de microesferas de alúmina termoexpandibles mediante medición de densidad real

    bigClick
  • Application Note
    Ceramics Application Notes collection

    2024-04-10

    Notas de aplicación para cerámica — Mejora de la eficiencia en la fabricación

    bigClick
  • Application Note
    Influence-of-Particle-Size-and-True-Density-of-Hollow-Glass-Microspheres-on-the-Compression-Strength

    2024-03-15

    Influencia del tamaño de las partículas y de la densidad real de las microesferas de vidrio huecas en la resistencia a la compresión

    bigClick

Más recursos

Analizador granulométrico relacionado

  • Bettersizer S3 Plus

    Bettersizer S3 Plus

    Analizador de tamaño y forma de partícula

    Rango de medición: 0,01 - 3.500μm (sistema láser)

    Rango de medición: 2 - 3.500μm (Sistema de imagen)

    Más información Solicitar un presupuesto
  • Bettersizer 2600

    Bettersizer 2600

    Analizador de tamaño de partículas por difracción láser

    Rango de medición: 0,02 - 2.600μm (Húmedo)

    Rango de medición: 0,1 - 2.600μm (en seco)

    Más información Solicitar un presupuesto
  • BeDensi T Pro Series

    BeDensi T Pro Series

    Solución económica para la medición de la densidad golpeada

    Número de puestos de trabajo: 1-3

    Velocidad de roscado: 100 - 300 machos/min.

    Repetibilidad: ≤1% de variación

    Más información Solicitar un presupuesto
  • BeVision D2

    BeVision D2

    Analizador dinámico de imágenes

    Tipo de dispersión: Seco

    Rango de medición: 30 - 10.000μm

    Tecnología Análisis dinámico de imágenes

    Más información Solicitar un presupuesto
  • PowderPro A1

    PowderPro A1

    Analizador automático de propiedades de polvos

    Modo de funcionamiento: Automático

    Velocidad de roscado: 50 - 300 machos/min.

    Repetibilidad: variación ≤3%.

    Más información Solicitar un presupuesto

  • Bettersizer 2600 Plus

    Analizador de tamaño y forma de partícula

    Rango de medición: 0,02–2600 μm (dispersión húmeda)

    Rango de medición: 0,1–2600 μm (dispersión seca)

    Rango de análisis por imagen dinámica: 2–3500 μm

    Más información Solicitar un presupuesto